ProductsIn assortment of our products - we provide you with a wide range of high-quality silicone products for civil and industrial use

more
ProductionOn our manufacture we use only advanced technology and innovation to achieve high quality products

more
GalleryGallery of objects where we picked up the best and you should pay attention and make the right choice

more
JobsOur company is always looking for professionals in their work, who are ready to prove it

more

Water repellent agent Unisil "Aquaproof" - water solution of potassium methylsiliconate for retail selling presented in in three different concentrations

Aquaproof Standart - ready for use solution of water repellent agent. Can be used immediately after opening

Aquaproof Concentate - should be diluted with water in ratio 1:3 before application.

Aquaproof Superconcentrate - should be diluted with water in ratio 1:10 before application.


The reasons to use Aquaproof:

Most of building materials of mineral origin have pores, so they have greater moisture absorption. Moistened materials significantly reduce the thermal insulation properties. Thus, the moistening of normal brick for just 10%, increases its thermal conductivity in 1,5 times.

Alternate freezing and thawing of water in the pores of stone materials, alternate wetting Features and drying, the disjoining effect of water films on the micro particles of these materials, chemical influences of aqueous solutions of salts, acids, alkalis, finally resulting to a strength reduction, are the main damaging factors decreasing the durability of constructions.

One of the most reliable, easy and cost saving ways of significant increasing the quality and durability of building materials is their water-repellency treatment with Aquaproof liquid.

"Aquaproof" can be used for:

• surface treatment of brick, concrete, foam concrete, shellstone, plastered surfaces, limestone, asbestos cement, slate, tile, marble, gypsum products, and other porous materials;

• bulk handling when prepare plaster, lime, cement, concrete solutions.

Treated materials have reduced water permeability and water absorption, increased frost-resistance and thermal insulation properties, anti-mold and anti-moss protection.

At the same time natural qualities of materials are preserved.

Preparation before use:

The application of the Aquaprok liquid in exterior water-repellency treatment when building and repair works will allow:

• to prolong the service life of buildings in 3 − 5 times, preventing fungi emergence and growth;

• to increase the frost resistance of buildings in the 2 − 3 times and corrosion resistance in 1,5 − 2 times;

• to reduce the water absorption in 1,5 times;

• to save heat by reducing of heat-transfer through the walls and ceilings;

• to avoid repeated efflorescence;

to improve the antisplash properties

 

Aquaproof Standart

Thoroughly clean surface of dirt, exfoliated areas of plaster, then blow dust with air (or sweep mechanically). If necessary, smooth the surface with appropriate building solution. Apply "Aquaproof" on dry surface with a brush, roller or sprayer until the termination of absorption. Do not allow sagging and leaving drops. Do not work when raining, and temperature lower than 5oC.

Note: reprocessing of the dry layer can lead to a white efflorescence.

Consumption of working solution depends on porosity of treated material and it averages 350 ml. per 1 m2.

Aquaproof Concentate

Thoroughly clean surface of dirt, exfoliated areas of plaster, then blow dust with air (or sweep mechanically). If necessary, smooth the surface with appropriate building solution.  Prepare working solution in proportion 1 liter of agent for 3 liters of water, in quantity necessary for 1−2 hours of work. Apply "Aquaproof" on dry surface with a brush, roller or sprayer until the termination of absorption. Do not allow sagging and leaving drops. Do not work when raining, and temperature lower than 5oC.

Note: reprocessing of the dry layer can lead to a white efflorescence.

Consumption of working solution depends on porosity of treated material and it averages 350 ml. per 1 m2.

Aquaproof Superconcentrate

Thoroughly clean surface of dirt, exfoliated areas of plaster, then blow dust with air (or sweep mechanically). If necessary, smooth the surface with appropriate building solution. Prepare working solution in proportion 1 liter of agent for 10 liters of water, in quantity necessary for 1-2 hours of work. Apply "Aquaproof" on dry surface with a brush, roller or sprayer until the termination of absorption. Do not allow sagging and leaving drops. Do not work when raining, and temperature lower than 5oC.

Note: reprocessing of the dry layer can lead to a white efflorescence.

Consumption of working solution depends on porosity of treated material

and it averages 350 ml. per 1 m2.

When preparation of building solutions and concrete the "Aquaproof" had to be introduced together with mixing water in amount of 0,75-1,5 % (Standart) or 0,1-0,2% (Concentrate) or 0,1-0,2%(Superconcentrate) by weight of the binder cement or lime.

Shelf life 12 months

 

Useful information
The main applications of silicon organic resins

The main applications of silicon organic resins

Silicone additives to concrete

Silicone additives to concrete

contacts  (+36) 56 52 11 15
© 2017 Hungarian Silicones. All rights reserved
Copying material from this site is prohibited
Created by MSGROUP
return_links(); ?>